1/7 n dedicated to 3.3v or battery supply (specified at 3v and 5v) n extremely low supply current : 9 m a typ / comparator n wide single supply range 2.7v to 16v n extremely low input current : 1pa typ n input common-mode voltage range includes gnd n fast response time : 2.5 m s typ for 5mv overdrive n pin-to-pin and functionally compati- ble with bipolar lm339 description the TS3V339 is a micropower quad cmos volt- age comparator with extremely low consumption of 9a typ / comparator (20 times less than bipolar lm339). similar performances are offered by the quad micropower comparator ts3v3704 with a push-pull cmos output. thus response times remain similar to the lm339. order code n = dual in line package (dip) d = small outline package (so) - also available in tape & reel (dt) p = thin shrink small outline package (tssop) - only available in tape & reel (pt) pin connections (top view) part number temperature range package ndp TS3V339i -40c, +125c n dip14 (plastic package) d so14 (plastic micropackage) p tssop14 (thin shrink small outline package) inverting input 2 output 2 non-inverting input 2 output 1 inverting input 1 non-inverting input 1 cc v - cc v 1 2 3 4 8 5 6 7 9 10 11 12 13 14 + output 3 output 4 non-inverting input 4 inverting input 4 non-inverting input 3 inverting input 3 - + - + - + - + TS3V339c,i,m 3v micropower quad cmos voltage comparators february 2002
TS3V339c,i,m 2/7 schematic diagram (for 1/4 TS3V339) absolute maximum ratings operating conditions symbol parameter value unit v cc + supply voltage 1) 1. all voltage values, except differential voltage, are with respect to network ground terminal. 18 v v id differential input voltage 2) 2. differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 18 v v i input voltage 3) 3. the magnitude of the input and the output voltages must never exceed the magnitude of the possitive supply voltage. 18 v v o output voltage 18 v i o output current 20 ma i f forward current in esd protection diodes on input 4) 4. guaranteed by design. 50 ma p d power dissipation 5) dip14 so14 tssop14 5. pd is calculated with t amb = +25c, t j = +150c and r thja = 80c/w for dip14 package = 150c/w for so14 package = 175c/w for tssop14 package 1500 830 710 mw t stg storage temperature range -65 to +150 c symbol parameter value unit v cc + supply voltage 2.7 to 16 v v icm common mode input voltage range 0 to v cc + -1.5 v t oper operating free-air temperature range TS3V339i -40 to +125 c t 1 t 2 1 tt 34 r t t t t 5 6 7 8 t t t 9 11 10 t 12 t 17 t 13 tt 14 15 t 16 t t 19 20 t 18 input - input + output cc v+ cc v-
TS3V339c,i,m 3/7 electrical characteristics v cc + = 3v, v cc - = 0v, t amb = 25c (unless otherwise specified) symbol parameter min. typ. max. unit v io input offset voltage 1) v ic = 1.5v t min . t amb t max. 1. the specified offset voltage is the maximun value required to drive the output up to 4.5v or down to 0.3v. 5 6.5 mv i io input offset voltage 2) v ic = 1.5v t min . t amb t max. 2. maximum values including unavoidable inaccuracies of the industrial test. 1 300 pa i ib input bias current (see note 2) v ic = 1.5v t min . t amb t max. 1 600 pa v icm input common mode voltage range t min . t amb t max 0 0 v cc + -1.2 v cc + -1.5 v cmr common-mode rejection ratio v ic = v icm min. 70 db svr supply voltage rejection ratio v cc + = 3v to 5v 70 db i oh high level output current v id = +1v, v oh = 3v t min . t amb t max. 240 1000 v v ol low level output voltage v id = -1v, i ol = +6ma t min . t amb t max. 400 550 800 mv i cc supply current (each comparator) no load - outputs low t min . t amb t max. 920 25 m a t plh response time low to high v ic = 0v, f = 10khz, r l = 5.1k w , c l = 50pf, overdrive = 5mv ttl input 1.5 0.7 m s t phl response time high to low v ic = 0v, f = 10khz, r l = 5.1k w , c l = 50pf, overdrive = 5mv ttl input 2.5 0.08 m s
TS3V339c,i,m 4/7 electrical characteristics v cc + = 5v, v cc - = 0v, t amb = 25c (unless otherwise specified) symbol parameter min. typ. max. unit v io input offset voltage 1) v ic = 2.5v t min . t amb t max. 1. the specified offset voltage is the maximun value required to drive the output up to 4.5v or down to 0.3v. 1.4 5 6.5 mv i io input offset voltage 2) v ic = 2.5v t min . t amb t max. 2. maximum values including unavoidable inaccuracies of the industrial test. 1 300 pa i ib input bias current (see note 2) v ic = 2.5v t min . t amb t max. 1 600 pa v icm input common mode voltage range t min . t amb t max 0 0 v cc + -1.2 v cc + -1.5 v cmr common-mode rejection ratio v ic = v icm min. 75 db svr supply voltage rejection ratio v cc + = +5v to +10v 85 db i oh high level output current v id = 1v, v oh = +5v t min . t amb t max. 240 1000 v v ol low level output voltage v id = -1v, i ol = 6ma t min . t amb t max. 260 400 650 mv i cc supply current (each comparator) no load - outputs low t min . t amb t max. 10 20 25 m a t plh response time low to high v ic = 0v, f = 10khz, r l = 5.1k w , c l = 15pf, overdrive = 5mv overdrive = 10mv overdrive = 20mv overdrive = 40mv ttl input 1.5 1.2 1.1 0.9 0.8 m s t phl response time high to lo< v ic = 0v, f = 10khz, r l = 5.1k w , c l = 15pf, overdrive = 5mv overdrive = 10mv overdrive = 20mv overdrive = 40mv ttl input 2.5 1.9 1.2 0.8 0.08 m s t f fall time f = 10khz, c l = 15pf, r l = 5.1k w , overdrive 50mv 25 ns
TS3V339c,i,m 5/7 package mechanical data 14 pins - plastic dip dimensions millimeters inches min. typ. max. min. typ. max. a1 0.51 0.020 b 1.39 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 d 20 0.787 e 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 f 7.1 0.280 i 5.1 0.201 l 3.3 0.130 z 1.27 2.54 0.050 0.100
TS3V339c,i,m 6/7 package mechanical data 14 pins - plastic micropackage (so) dimensions millimeters inches min. typ. max. min. typ. max. a 1.75 0.069 a1 0.1 0.2 0.004 0.008 a2 1.6 0.063 b 0.35 0.46 0.014 0.018 b1 0.19 0.25 0.007 0.010 c 0.5 0.020 c1 45 (typ.) d (1) 8.55 8.75 0.336 0.344 e 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 7.62 0.300 f (1) 3.8 4.0 0.150 0.157 g 4.6 5.3 0.181 0.208 l 0.5 1.27 0.020 0.050 m 0.68 0.027 s 8 (max.) note : (1) d and f do not include mold flash or protrusions - mold flash or protrusions shall not exceed 0.15mm (.066 inc) only for data book. d m f 14 1 7 8 b e3 e e lg c c1 a a2 a1 b1 s
TS3V339c,i,m 7/7 package mechanical data 14 pins - thin shrink small outline package (tssop) dimensions millimeters inches min. typ. max. min. typ. max. a 1.20 0.05 a1 0.05 0.15 0.01 0.006 a2 0.80 1.00 1.05 0.031 0.039 0.041 b 0.19 0.30 0.007 0.15 c 0.09 0.20 0.003 0.012 d 4.90 5.00 5.10 0.192 0.196 0.20 e 6.40 0.252 e1 4.30 4.40 4.50 0.169 0.173 0.177 e 0.65 0.025 k 0 8 0 8 l 0.450 0.600 0.750 0.018 0.024 0.030 l1 1.00 0.039 aaa 0.100 0.004 c e1 k l e e b d pin 1 identification 1 7 8 14 seating plane c aaa c 0,25 mm .010 inch gage plane l1 a a2 a1 information furnished is believed to be accurate and reliable. however, stmicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of stmicroelectronics. specifications mentioned in this publication are subject to change without notice. this publication supersedes and replaces all information previously supplied. stmicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of stmicroelectronics. ? the st logo is a registered trademark of stmicroelectronics ? 2002 stmicroelectronics - printed in italy - all rights reserved stmicroelectronics group of companies australia - brazil - canada - china - finland - france - germany - hong kong - india - israel - italy - japan - malaysia malta - morocco - singapore - spain - sweden - switzerland - united kingdom - united states ? http://www.st.com
|
